Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen gezeigt.
|
tabelle_der_laserparameter [2020/03/24 09:39] jakub.dlouhy |
tabelle_der_laserparameter [2023/03/21 09:44] |
||
|---|---|---|---|
| Zeile 1: | Zeile 1: | ||
| - | ====== Tabelle der Laserparameter ====== | ||
| - | Abgestimmt auf den ZING 6030 mit 40 Watt Laserleistung. | ||
| - | |||
| - | |||
| - | Vektor = Schneiden / Frequenz in Hz; Raster = Gravieren / Auflösung in DPI | ||
| - | ---- | ||
| - | ==== Holzprodukte ==== | ||
| - | ^ Material ^ Dicke ^ Modus ^ Speed ^ Power ^ Hz/DPI ^ Anmerkungen ^ | ||
| - | | Finnpappe | 2 mm | Vektor | 100 | 45 | 500 | | | ||
| - | | Finnpappe | – | Raster | 100 | 25 | 400 | (pat) gut | | ||
| - | | HDF | 3 mm | Vektor | 30 | 100 | 1000 | | | ||
| - | | Kork | 3 mm | Vektor | 45 | 100 | 25 | (pat) nass machen, verhindert Schmauchspuren | | ||
| - | | Kork | 5 mm | Vektor | 15 | 100 | 25 | (pat) nass machen, verhindert Schmauchspuren | | ||
| - | | Kork | – | Raster | 100 | 20 | 400 | (pat) sehr guter Kontrast | | ||
| - | | MDF | 2 mm | Vektor | 50 | 40 | 1000 | (pat) sehr gut | | ||
| - | | MDF | 3 mm | Vektor | 50 | 50 | 1000 | (pat) sehr gut | | ||
| - | | MDF | 5 mm | Vektor | 15 | 100 | 1000 | (pat) gut | | ||
| - | | MDF | – | Raster | 80 | 60 | 400 | | | ||
| - | | MDF | – | Write | 100 | 10 | 1000 | (pat) Schreiben mit der Schneideinstellung | | ||
| - | | Sperrholz (Birke) | 2 mm | Vektor | 30 | 55 | 1000 | | | ||
| - | | Sperrholz (Birke) | – | Raster | 50 | 35 | 400 | | | ||
| - | | Leimholz (Buche) | – | Raster | 80 | 65 | 400 | (pat) quer zur Maserung gravieren | | ||
| - | | | | | | | | | | ||
| - | | | | | | | | | | ||
| - | | | | | | | | | | ||
| - | | | | | | | | | | ||
| - | | | | | | | | | | ||
| - | |||
| - | ==== Kunststoffe / Verbundmaterialien ==== | ||
| - | ^ Material ^ Dicke ^ Modus ^ Speed ^ Power ^ Hz/DPI ^ Anmerkungen ^ | ||
| - | | Acrylglas | 2 mm | Vektor | 55 | 70 | 5000 | (pat) perfekt | | ||
| - | | Acrylglas | 3 mm | Vektor | 40 | 70 | 5000 | (pat) sehr gut | | ||
| - | | Acryglas | – | Raster | 100 | 40 | 400 | | | ||
| - | | Acetat-Folie (Ultraphan) | 0,1 mm | Vektor | 80 | 4 | 500 | (pat) sehr gut | | ||
| - | | Hartgewebe | 1 mm | Vektor | 20 | 100 | 1000 | (pat) ok, Schmauchspuren | | ||
| - | | Moosgummi | 2 mm | Vektor | 30 | 8 | 5000 | | | ||
| - | | Moosgummi | – | Raster | 100 | 60 | 400 | (pat) s/w Kontrast ist ok | | ||
| - | | PE | 3 mm | Vektor | 80 | 50 | 500 | (pat) ok, Schmauchspuren | | ||
| - | | PET Laser-Spiegelfolie | 0,1 mm | Vektor | 100 | 3 | 500 | (pat) gut am Tisch fixieren, Aslanfolie | | ||
| - | | PET-G | 0,5 mm | Vektor | 100 | 25 | 1500 | | | ||
| - | | PP | 0,5 mm | Vektor | 80 | 30 | 500 | (pat) gut, leichter Schmelzrand | | ||
| - | | PP | – | Raster | 80 | 50 | 400 | (pat) dezent lesbar, schmilzt bei zu viel Power | | ||
| - | | Silikon | 0,5 mm | Vektor | 100 | 30 | 500 | | | ||
| - | | Stempelgummi | 2,3 mm | Vektor | 25 | 100 | 250 | (pat) gut, danach mit Wasser+Spühlmittel lange auswaschen | | ||
| - | | Stempelgummi | – | Raster | 20 | 100 | 500 | (pat) Dokument = Druckgröße, Einfassung deakt., Schulter 6/Steg 1, Spiegeln | | ||
| - | | | | | | | | | | ||
| - | | | | | | | | | | ||
| - | | | | | | | | | | ||
| - | | | | | | | | | | ||
| - | |||
| - | ==== Sonstiges ==== | ||
| - | ^ Material ^ Dicke ^ Modus ^ Speed ^ Power ^ Hz/DPI ^ Anmerkungen ^ | ||
| - | | Bastel- und Dekofilz | 1 mm | Vektor | 40 | 5 | 500 | (pat) gut | | ||
| - | | Jute (grob) | 2 mm | Vektor | 100 | 55 | 500 | (pat) ok | | ||
| - | | Glas | – | Raster | 30 | 60 | 500 | (pat) mit nassem Küchenkrepp belegen | | ||
| - | | Granit | – | Raster | 70 | 25 | 500 | (pat) gut, zuviel Power führt zu Glasbildung | | ||
| - | | Thermofaxgewebe | – | Raster | 50 | 5 | 400 | (pat) Dithering an, am Rand fokusieren | | ||
| - | | | | | | | | | | ||
| - | | | | | | | | | | ||
| - | | | | | | | | | | ||
| - | | | | | | | | | | ||
| - | | | | | | | | | | ||
| - | |||
| - | |||
| - | |||
| - | Impressum: https://vinnlab.th-wildau.de/imprint/ | ||